Round Flex Liner Components

Connectors: Adjustable elbows and chimney liner connectors make it easy to connect stainless steel flex chimney liner components together. You can use these connectors for stainless steel flue liners or other ss chimney liner items to make sure you get a great fit with an airtight connection. Possibly you will need our high temp silicone for added security Everguard Chimney Silicone. Keep Rockford Chimney Supply in mind for all your stainless steel chimney parts required to get the job done.

Adjustable and Fixed Elbows

Our Flex Liner Elbows have laser welded seams for smooth adjusting. These elbows have a female end to accept the flex liner. No adapter needed! If you need an elbow for rigid liner or black pipe see our rigid lining kits page.

Tee Extension Slip Connector

This connector's male end slips inside the snout of our tee. It allows you to add 8 to 16 inches simply by sliding it in or pulling it out of the tee snout. A perfect fit, with no cutting required! The expanded end of the slip connector is female with an interior diameter 1/16" larger than the standard pipe it connects to. Perfect for when you need to add length to the horizontal snout of the tee.

Gas Take Off Connector

Use this to connect a hot water pipe above an appliance. Make a hole in the horizontal pipe using a hole saw with your drill set to reverse. Seal with high heat mill pack and you're done. The gas take off measures 10 inches in length.

Flue Liner Appliance Connector

This little guy comes in every size you can imagine. It is the most used connector we stock. The liner fits into the female side, utilizing the quick connect band. The other end is crimped and ready for your appliance, fireplace, stove, or rigid stainless steel liner pipe. A perfect round fit every time thanks to the smooth weld technology.

Round Liner to Liner Connector

This dripless female to male chimney flex chimney lining connector / couple connects flex to almost anything. Smooth butt welded seam allows for an air tight connection A great item to have on the job site.

Male to Male Liner Coupler

Are you in a tight spot? For tight clearance relining situations, this male to male chimney liner connector is just the ticket!!! This part is not dripless, and will require screws or rivets. The smooth butt welded seam makes this part slide together like butter, crimped on both ends!

Standard Tee with 10" snout

Zip Zip and you're done! Features a removable 10" long snout, a secure inside removable clamp connection and the quick connect band. Note: if you need the snout to be less than 10" simply cut it down with a hack saw. Clean out cap included. Distance from below the snout to bottom of tee is 3.5".

3" to 4" Pellet Tee

Connects a 3" pellet stove to 4" liner. This connector has a 3" fixed snout and the quick connect band. Clean out cap included.

Standard Tee with 22" snout

Need more length, this tee and tee cap has the quick connect band and the snout measures 22" long. Note: if you need the snout to be less than 22" simply cut it down with a hack saw. Clean out cap included. Distance from below the snout to bottom of tee is 3.5".

Short Body Tee with 10" snout

This is a short body tee with 10" snout for constricted thimble installations. Note: if you need the snout to be less than 10" simply cut it down with a hack saw. No clean out available due to the short body size. Distance from below the snout to bottom of tee is 3/4".

Short Body Tee with 22" snout

This is a short body tee with 22" snout for constricted thimble installations. Note: if you need the snout to be less than 22" simply cut it down with a hack saw. No clean out available due to the short body size. Distance from below the snout to bottom of tee is 3/4"

Custom Removable Double Snouted Tee with Tee cap

A tee with two take offs, it is designed to allow you to connect two appliances to one chimney liner. Select any two snout diameters from 3 inch through 8 inch. The standard snout length is 10 inches. The tee connector will extend 3 inches above the top snout and 3 inches below the bottom snout. Please enter your measurements in the form below.

22" Tee Snout

22" Quick Connect Snout without the Tee body and clean out cap.

Top Plates: Rockford offers a wide variety of top plates in our chimney liner supply products, including components for stainless steel flue liners. Instructions are provided, including how to install a rain guard on a chimney cap!
Everything Ships Free to the Lower 48 US States

No Sag Top Plate

No Sag, No clamps, flashing, or storm collars needed. Just pull the liner through the collar and tighten the quick connector band.

Terra-Cotta Top Plate

Fastens right on the terra-cotta flue tile. The top plate screws to the tile like a rain cap and gives a great no hassle, finished look. You will love it!

See our Terra Cotta Top Plate Sizing Chart.

Flat Top Plate

For those chimney tops that need to be custom fitted we offer our flat top plate. Simply trim it to fit with a pair of snips and it's ready for installation.

Deluxe Hinged Flat Cap

The Deluxe Flat Hinged Top Termination Top Plate Mount attaches to chimneys with NO clay tile exposed at the chimney top. Using masonry screws simply screw the top plate to the brick, block, masonry chimney top. Easy and simple installation! For flexible chimney liners only.

Deluxe Hinged Cap Terra Cotta Mount

The Deluxe Terra Cotta Hinged Top Termination Terra Cotta Clay Lining Mount attaches to chimneys with exposed clay tile at the chimney top. Simply insert the stainless steel screws into the skirting of the top plate and snug them up to the exposed clay tile at the top of your chimney. Easy and simple installation! For flexible chimney liners only.

Chase Covers

Chase Cover - Top Termination Flue Covers. Our specialty, any size, any shape copper or stainless steel multiple vents, the list goes on, it's all up to you. Think twice before using galvanized as these repairs are only temporary. Stainless or copper chimney covers will last a lifetime. For pricing on chase covers from 16"x16" all the way to 100"x 100" click here: copper or stainless steel. Chimney support brackets and more.

Round Rain Cap Top Plate Mount

Round Quick Connect Rain Cap with screen and wind guard. Fasten down the quick connect clamp to the collar of the flex liner Top Plate or Chase Cover and you're done! Sharp looking too! In a tornado your roof will come off before this tears off. And it installs in a snap!

Square Rain Cap Top Plate Mount

Square Quick Connect Flue Cap with mesh screen. Fasten down the quick connect clamp to the collar of a flex liner Top Plate or Chase Cover and you're done! The sharpest looking rain caps on todays market, and they install in a snap!

Vacu-Stack Non Air Cooled Cap

This is the premier chimney cap for solving common, wind-related chimney draft problems. Wind-induced downdraft can cause smoke to enter the living space when: hills, mountains, tall trees, and/or tall buildings are in the vicinity. Vacu-Stack also functions as a conventional chimney cap by protecting the chimney from rain, snow, debris, and animals.

Application: Single wall insulated class A chimney pipe or chimney liner.

How Does It Work?

WeatherShield Non Air Cooled Chimney Cap

A unique alternative to the traditional chimney cap. Its 304 stainless steel construction assures superior corrosion resistance to weather and the hostile flue gas environment. Despite adverse weather, the WeatherShield will not rust. For use with solid pack Class A, masonry and single wall chimneys to keep the rain, snow, leaves and animals out, but keeps sparks in.